Energy technology: wind power, generators, large motors
Measuring the bearing gap in wind turbines
To date, bearing gaps were measured during standstill based on a tactile principle. Therefore, long inspection intervals were required, which in turn, may increase the risk of a complete plant failure. Moreover, these deliberate stoppages intended for measuring and inspection purposes cause considerable additional costs. Micro-Epsilon acquires the measurement values during plant operation, thereby enabling reliable, cost-saving real-time analysis.
This measurement task is performed with the inductive eddyNCDT 3005 measuring system based on eddy currents. It includes a sensor with a measuring range up to 6 mm, which is permanently connected to the controller via a 1 m long cable. As the system is oil-tight both on the front and rear side, it is ideally suited to this application even when typical oil pressures reach 1 to 2 bar in the bearing. The eddyNCDT 3005 inductive system is already being used in wind turbines to analyse and optimise the maintenance intervals of wind turbines. In addition, the data acquired in the test bench throughout the design period can be taken into account and used for dimensioning purposes of new components. The sensors can be used in the test bench and in high volume applications for Condition Monitoring. Serial use offers major advantages as the sensor technology can already be aligned and precisely adjusted during installation and initial operation.
Alignment of solar panels
Aligning solar panels in relation to the course of the sun increases the energy yield, and therefore the plant effectiveness. Inclination sensors ensure that the panels are always properly aligned.
Rotor stress tests in the test bench
Test rigs have been developed for load tests on wind turbine rotor blades and simulate the real loads caused by high winds and weather. The tip of the rotor blade can be distorted by up to 10m due to mechanical loads. Draw-wire sensors are used on the test rig for measuring the distortion. Two sensors per traction point measure the deflection and torsion of the rotor blade. The draw-wire sensors operate with measuring ranges between 3 m and 10 m. The digital signal output is provided for further simulations.
Rotor gap measurement in the generator
In order to monitor rotor behaviour in the generator, capacitive displacement sensors measure the gap between stator and rotor. Despite high temperatures and electromagnetic fields, capacitive sensors from Micro-Epsilon provide unmatched accuracies. In addition to continuous measurement for predictive maintenance, the measurement can also be used when setting the generator.
Recommended sensor technologyCapacitive displacement, distance and position sensors
Monitoring the air flap openings
In order to control air supply, the air flaps automatically open and close depending on the temperature. Draw-wire displacement sensors monitor the position of the open air flap.
Monitoring the tower oscillation
Acceleration sensors are used in wind turbines in order to monitor the tower oscillation. When the oscillation is too strong, the rotor blades are removed from the wind.
Supporting moments of the nacelle
In order to monitor the supporting moments, eddy current displacement sensors measure the distance between the nacelle and the tower, which enables early recognition of any fluctuations. Therefore, the plant can be switched off in time when the wind load is too high.
Measuring the foundation movement
Laser triangulation sensors measure the distance from the foundation in order to detect the tower movements. High measuring rates enable to detect vibrations directly. Depending on the number of sensors installed, detailed evaluations about the vibration behaviour can be determined. When the tower movement is too strong, the rotor blades are removed from the wind in order to avoid possible damage.
Recommended sensor technologyNew: Smart Laser Displacement, Distance and Position Sensor
Measuring the deflection of the clutch disc
Eddy current displacement sensors measure the axial, radial or tangential deflection of the clutch disc. These robust sensors are designed for harsh ambient conditions and, due to their extremely compact size, can also be integrated in restricted installation spaces. The sensor provides stable measurement results despite high pressures and temperatures.
Measuring the temperature of frictional heat on bearings
The gearbox temperature in wind turbines is measured continuously during operation. Heating up of components may indicate a potential problem with a component. If a certain threshold is exceeded, subsequent remedial action can be started or maintenance planned.
Recommended sensor technologyInfrared Temperature Sensors & Thermal Imaging Cameras
Oil gap measurement in shafts
With regard to predictive maintenance, the oil gap should be measured, i.e. the distance between the bearing surface and the shaft filled with lubricants. Despite pressure, high temperatures and lubricants, robust eddy current sensors from Micro-Epsilon can provide a permanent statement about the lubricating gap based on high measurement accuracy.